Automatic Technology Australia Elite Installationshandbuch PDF herunterladen (Seite 16)

MODE SELECTION

If the P.E. input is configured to stop the gate during opening or

closing, then the gate can auto-close from a midway position. This

feature is implemented so that once a vehicle has entered the gate-

way and broken the P.E. beam, the gate will stop. When the P.E.

beam is cleared the gate will auto-close from the stopped position.

This results in the gate not having to fully open and thus reducing

the time unwarranted access through the gate is possible. The

factory set delay time of 1 second is adjustable, see section “P.E.

TRIGGERED AUTO-CLOSE DELAY TIME” below.

MIXING AUTO-CLOSE MODES

The PEDESTRIAN AUTO-CLS mode and the STANDARD

AUTO-CLS mode do not affect each other as one operates during

standard operation and the other during pedestrian access.

However it is possible to have P.E. triggered pedestrian auto-close

by selecting both the PEDESTRIAN AUTO-CLS and P.E.

TRIGGERED AUTO-CLS modes. In this case the gate would

partly open for pedestrian access and then either the P.E.

TRIGGERED AUTO-CLS would cause the gate to auto-close

when a pedestrian walks through and activates the P.E beam or, if

no one walked through the PEDESTRIAN AUTO-CLS would

close the gate. This way the gate is only kept open long enough

for a person to walk through, but with the backup that if no one

walks through the gate will still close. The same concept can be

used with standard operation by selecting both the STANDARD

AUTO-CLS and the P.E. TRIGGERED AUTO-CLS modes. That

is, the gate would only stay open long enough for the vehicle to

pass through but would still auto-close if no vehicle enters.

Note: P.E. TRIGGERED AUTO-CLS will not operate during

pedestrian access unless the PEDESTRIAN AUTO-CLS mode is

also selected.

MODE SETTING ADJUSTMENT

This section describes how to adjust several parameters via the

control boards buttons and dials. Other adjustments can be

performed by use of the advanced technicians Control Board

Instruction Manual and Programmer. Contact your local ATA

dealer for a copy.

SYNCHRONISING DELAY TIME

The synchronising delay time is adjusted using the 'SYNC delay

timer' button. The synchronising delay time is adjustable in 0.1

second steps. The factory set default is 2 seconds.

STANDARD AUTO-CLOSE DELAY TIME

The standard auto-close delay time is adjusted using the 'STD

auto-close' button. Delay time is adjustable in 1 second steps. The

factory set default is 30 seconds.

PEDESTRIAN ACCESS AUTO-CLOSE DELAY TIME

The pedestrian auto-close delay time is adjusted using the 'PED

auto-close' button. Delay time is adjustable in 1 second steps. The

factory set default is 15 seconds.

P.E. TRIGGERED AUTO-CLOSE DELAY TIME

The P.E. triggered auto-close delay time is adjusted using the

'P.E. auto-close' button. Delay time is adjustable in 1 second steps.

The factory set default is “off”.

PEDESTRIAN ACCESS CYCLE TIME

The pedestrian access cycle time sets how far gate leaf 1 opens for

pedestrian access.

1. Drive the gate to the closed position using the OSC button or

another control input.

2. Press and hold the 'PED cycle timer' button. The gate leaf

driven by motor 1 will start to open.

3. When the gate leaf has reached a position suitable for

pedestrian access, release the button.

4. The pedestrian access drive timer has now been set. Either

press the OSC button and exit the time set mode or continue

setting one of the synchronising delay or auto-close times.

SLOW MOTOR SPEED

IMPORTANT: Please make sure that the gate(s) are in the open

position before proceeding with steps 1 to 5 below.

The speed the motor slows down towards the end of a cycle can

be adjusted using the following procedure. The factory set

default slow speed is set to “ 3”

1. Note the current maximum speed selected by the speed

selection dial.

2. Using the speed selection dial select the desired slow speed.

3. Press and hold the 'RESET' button and count five (5) flashes of

the OPEN status led.

4. Release button.

5. Place the speed selection dial back to the desired maximum

speed .

ADJUSTING AUTO-CLOSE AND SYNC DELAY TIMES

1. Press and hold the required button for the desired time.

2. Release button.

3. Press the OSC button to exit the time setting mode or restart

from step 1 to set another time.

Notes:

a) The time setting mode is indicated by both the OPEN and

CLOSE status LED's being off.

b) Each flash of the OPN led represents 1 second.

c) When a button is first pressed, the CLOSE status LED turns

on. The time delay is set to zero when the CLOSE LED turns

off and then increases for as long as the button is held.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Automatic Technology Australia Elite Installationshandbuch Seite 16

Kommentare zu diesen Handbüchern